Solvent effect in polymer analysis by MALDI-TOF mass spectrometry

Solvent effect is one of the important factors in sample preparation which may affect matrix-assisted laser desorption/ionization time-of-flight (MALDI-TOF) mass spectra of synthetic polymers. MALDI imaging, a useful imaging tool for discovering biomarkers in tissues, is applied here for better comprehension of solvent effect in polymer analysis by MALDI-TOF mass spectrometry. Nylon-6 was chosen as a model polymer for the study of solvent effect. Its MALDI mass spectra in different solvents were performed. MALDI imaging analysis was performed for studying the incorporation of analytes into matrix crystals in different solvent combinations. Specifically, the colocalization of matrix and analyte was obtained through Pearson’s correlation (PC) coefficient analysis of their MALDI images. The results demonstrated that satisfactory spectra were obtained in higher PC value conditions. PC decreased along with an increase in the ratio of poor solvent, which suggested that we should minimize the poor solvent ratio to obtain better MALDI spectra.     

Facile one-step extraction and oxidative carboxylation of cellulose nanocrystals through hydrothermal reaction by using mixed inorganic acids

A facile and efficient approach to prepare carboxylated cellulose nanocrystals (CCNCs) is presented through a novel one-step hydrothermal procedure by using a mixed acid system of hydrochloric acid and nitric acid (HCl/HNO₃). The as-prepared cellulose nanoparticles were characterized by scanning electron microscopy, wide angle X-ray diffraction, conductometric titrations, Fourier transform infrared spectrometry and thermal gravimetric analysis. The results showed that the combination of the mixed acid and hydrothermal reaction can speed up the process of CCNC preparation, and then high quality of the product could be obtained at relatively low acid concentration. It is found that the addition of nitric acid could not only promote the conversion of surface groups on the cellulose nanocrystals (CNCs), but also have significant influences on the yield, particle size and microstructure of CNCs. For the volume ratio of HCl/HNO₃ of 7:3, the as-prepared CCNCs exhibited the largest length to diameter ratio and narrowest dimension distributions as well as maximum degree of oxidation of 0.12. In addition, high dispersion stability for the CCNCs could be observed due to the existence of negative carboxyl groups. This approach based on one-step oxidative carboxylation greatly simplified the preparation of CCNCs with high yield and high crystallinity under mild hydrothermal condition.     

Sensitive voltammetric method for the fast analysis of the antioxidant pyrogallol using a boron-doped diamond electrode in biofuels

A sensitive voltammetric method for the determination of pyrogallol (PY) was developed employing a boron-doped diamond electrode (BDDE). The composition of the supporting electrolyte was investigated during the development of the methodology. Linear sweep voltammetry (LSV) under the optimized experimental conditions was applied for PY determination with a limit of detection and limit of quantification of 0.85 and 2.82 μmol L^?1, respectively. These values are satisfactory for application to real samples. The usability of this method for the quantification of pyrogallol was in range from 2.82 to 296.00 μmol L^?1. Finally, the developed method was successfully used for the analysis of real samples of biodiesel produced from rapeseed oil and its blend with diesel fuel. Samples of biodiesel and biodiesel blends were analyzed directly in an electrochemical cell, while samples with very low concentrations of PY in biodiesel were extracted with water using the proposed simple and fast process.     

Preparation and CO2 capture properties of nanocrystalline Li2ZrO3 via an epoxide-mediated sol–gel process

Journal of Sol-Gel Science and Technology - Nanocrystalline lithium zirconate (Li2ZrO3) was successfully prepared by an epoxide-mediated sol–gel process. The compositions and morphologies of...     

聚羟基丁酸酯/碳纳米管复合纳米纤维膜的制备及其对重金属离子吸附分离性能的研究

以聚羟基丁酸酯和碳纳米管为原料,采用三氯甲烷/二甲基甲酰胺混合溶液为溶剂,利用静电纺丝技术制备了聚羟基丁酸酯/碳纳米管复合纳米纤维膜.研究了碳纳米管的含量对纳米纤维膜形貌和力学性能的影响,探讨了复合纳米纤维膜对重金属Cu(II)、Cd(II)和Pb(II)的吸附特性.实验结果表明:加入1 wt%碳纳米管能够将纳米纤维的平均直径从(728±146)nm降低至(468±89)nm,纳米纤维膜的比表面积从27.24 m~2/g提高至43.45 m~2/g;碳纳米管的复合能够有效增强聚羟基丁酸酯纳米纤维,当碳纳米管含量1 wt%为最佳,拉伸强度可达5.85 MPa,较纯聚羟基丁酸酯纳米纤维提升了115%.复合纳米纤维膜对重金属离子具有良好的吸附特性,其对Cu(II)、Cd(II)和Pb(II)的最佳吸附pH值为5,此时最大吸附容量分别为91.04、171.05和197.03mg/g,平衡吸附时间分别约为50、60和60 min,吸附率分别为1.79、2.83和3.28 mg/g/min;热力学和动力学分析表明,复合纳米纤维膜对重金属Cu(II)、Cd(II)和Pb(II)的吸附行为更符合Freundlich模型,吸附过程更符合Pseudo-second order模型;循环使用实验表明,重复使用5次后,其吸附容量可保持在初始值的87%以上,具有较好的使用寿命.     

一种吲哚螺吡咯多取代杂环化合物的合成及其晶体结构

利用多组分1,3偶极环加成反应方法,合成了一种新的螺环结构1'-甲基-3'-吡啶甲酰基-4'-(2-噻吩基)螺[吲哚啉-3,2'-吡咯啉]-2-酮化合物,并对该化合物进行了红外光谱、核磁共振谱及X-射线单晶衍射表征.单晶衍射结果表明:该晶体属于三斜晶系,空间群为P-1,晶体参数为a=0.899 9(1)nm,b=0.914 4(1)nm,c=1.271 1(2)nm,α=92.852(1)°,β=107.305(2)°,γ=101.580(1)°.在分子晶体结构中,吡咯啉环采用了信封式构象,通过螺碳原子与吲哚啉环相连,形成刚性螺环结构,2个环接近垂直构型,其二面角为84.15(2)°.     

过渡元素掺杂Fe_3O_4(001)表面磁电性能的理论研究

采用基于密度泛函理论的第一性原理方法,计算Fe_3O_4,Fe_3O_4(001)表面以及过渡元素掺杂表面的电子结构和磁性。结果表明Fe_3O_4的半金属性主要来源于B位Fe离子,并且Fe的3d轨道发生强烈自旋极化;比较(001)表面不同终端A和B终端的表面能和电子结构,得出两种终端稳定性存在差异且A终端较稳定同时表现半金属性;由过渡元素V、Cr、Mn、Co、Cu和Zn取代Fe_3O_4(001)表面A终端A位Fe进行掺杂,形成的6种新表面结构都保持了半金属性。对比它们的表面能和磁矩,Mn掺杂的表面结构最稳定并且磁矩明显增大。     

Antibacterial membranes based on chitosan and quaternary ammonium salts modified nanocrystalline cellulose

Etherification of nanocrystalline cellulose (NCC) with three kinds of quaternary ammonium salts epoxypropyltrimethylammonium chloride, N,N‐dimethyl‐N‐dodecyl‐N‐(1,2‐epoxypropyl) ammonium chloride (DMDEPAC), and N,N‐dimethyl‐N‐octadecyl‐N‐(1,2‐epoxypropyl) ammonium chloride (DMOEPAC) was successfully performed via a nucleophilic addition reaction. The synthesized DMDEPAC and DMOEPAC were characterized by nuclear magnetic resonance. The modified NCC particles, NCC epoxypropyltrimethylammonium chloride, NCC‐DMDEPAC, and NCC‐DMOEPAC, were characterized by energy dispersive spectrometer. Nanocomposite films based on chitosan (CS) containing quaternary ammonium salts modified NCC were prepared with nanoparticle loadings of 5.0, 7.5, and 10.0%, respectively. The effect of nanoparticle content on the tensile strength of composite films was studied. The results indicated that the films with 5.0% nanoparticle loading exhibited the biggest increase in tensile strength. Surface morphology, smoothness, and antibacterial properties of composite films containing 5% modified NCC were also studied. CS/NCC‐DMDEPAC‐5.0 and CS/NCC‐DMOEPAC‐5.0 displayed excellent biocidal abilities against both Gram‐positive Staphylococcus aureus (ATCC 6538) and Gram‐negative Escherichia coli O157:H7 (ATCC 43895). The bio‐based nanocomposite films with increased mechanical strength and excellent antibacterial properties show great potential as food packaging materials. Copyright © 2017 John Wiley & Sons, Ltd.     

Modified classification of non-self-adjoint second-order difference equations

This paper is concerned with the classification of non-self-adjoint second-order difference equations. The relationship between the number of summable solutions of non-self-adjoint difference equations and that of the discrete linear Hamiltonian system is discussed. A classification for non-self-adjoint second-order difference equations is established, which is independent of the choice of the rotated half plane and the fixed point.